Current Limiting

Current limiting is the practice of imposing a limit on the current that may be delivered to a load to protect the circuit generating or transmitting the current from harmful effects due to a short-circuit or overload. The term "current limiting" is also used to define a type of overcurrent protective device. According to the 2020 NEC/NFPA 70, a current limiting overcurrent protective device is defined as, "A device that, when interrupting currents in its current-limiting range, reduces the current flowing in the faulted circuit to a magnitude substantially less than that obtainable in the same circuit if the device were replaced with a solid conductor having compatible impedance."

Inrush current limiting

An inrush current limiter is a device or group of devices used to limit inrush current. Passive resistive components such as resistors or negative temperature coefficient (NTC) thermistors are simple options, with power dissipation and cool-down time being their main drawbacks, respectively. More complex solutions using active components can be used when more straightforward options are unsuitable.

In electronic power circuits

Some electronic circuits employ active current limiting since a fuse may not protect solid-state devices.

One style of current limiting circuit is shown in the image. The schematic represents a simple protection mechanism used in regulated DC supplies and class-AB power amplifiers.

Q1 is the pass or output transistor. R_sens is the load current sensing device. Q2 is the protection transistor which turns on as soon as the voltage across R_sens becomes about 0.65 V. This voltage is determined by the value of R_sens and the load current through it (I_load). When Q2 turns on, it removes base current from Q1, thereby reducing the collector current of Q1, which is nearly the load current. Thus, R_sens fixes the maximum current to a value given by 0.65/R_sens. For example, if R_sens = 0.33 Ω, the current is limited to about 2 A even if R_load becomes a short (and V_o becomes zero).

Further, this power dissipation will remain as long as the overload exists, which means that the devices must be capable of withstanding it for a substantial period. This power dissipation will be substantially less than if no current limiting circuit had been provided. In this technique, beyond the current limit, the output voltage will decrease to a value depending on the current limit and load resistance.

To reduce the heat that must be dissipated by the pass devices under a short-circuit, ''foldback'' current limiting is used, which reduces current in the short-circuit case. Under a short circuit, where the output voltage has reduced to zero, the current is typically limited to a small fraction of the maximum current.

The prime purpose of foldback current limiting in linear power supplies is to keep the output transistor within its safe power dissipation limit. A linear regulator dissipates the difference between input and output voltages as heat. Under overload conditions, the output voltage falls, so the difference becomes larger, thus increasing dissipation. Foldback helps to keep the output transistor within its safe operating area under fault and overload conditions. Foldback also significantly reduces the power dissipation in the load in fault conditions, which can reduce the risks of fire and heat damage.

Many power supplies employ constant current limiting protection; foldback goes one step further by linearly reducing the output current limit as output voltage decreases. However, it adds complexity to the power supply. It can trigger "lockout" conditions with non- ohmic devices that draw a constant current independent of supply voltage (such as op-amps). A foldback current limiter may also employ a transient delay to avoid lockout and limit localized heating at the short circuit.

A switched-mode power supply operating at the current limit with the output short-circuited does not have increased power dissipation in the power transistor(s), so foldback current limiting is an application feature only rather than one that also prevents a load fault from also destroying the power supply. The safety benefit of reducing the power delivered to a short circuit in the load is proportional to the operating current limit. Foldback current limiting is most likely to be found in a switchmode power supply when it is a component in a product that is independently certified to meet regional safety standards.

Single power-supply circuits

An issue with the previous circuit is that Q1 will not be saturated unless its base is biased about 0.5 volts above V.

These circuits operate more efficiently from a single (V) supply. In both circuits, R1 allows Q1 to turn on and pass voltage and current to the load. When the current through R_sense exceeds the design limit, Q2 turns on, which in turn begins to turn off Q1, thus limiting the load current. The optional component R2 protects Q2 in the event of a short-circuited load. When V is at least a few volts, a MOSFET can be used for Q1 for lower dropout voltage. Due to its simplicity, this circuit is sometimes used as a current source for high-power LEDs.

File:Ограничение извести с помощью NPN-транзисторов.png, Current limiter with NPN transistors (''Vo'' output is located at similar location as PNP example)
File:Ограничение извести с помощью PNP-транзисторов.png, Current limiter with PNP transistors

See also

* Current source
* Crowbar
* Electrical ballast
* Fault current limiter

References

External links

Current Limiting for Stepper Motors

Current limiting resistor calculator for LED arrays

Constant current & foldback current limiting

{{DEFAULTSORT:Current Limiting
Analog circuits
Limiting
Electrical power control
Over-current protection devices